DIY Solar Pumping Station PSAMR3FV1TW201- Twin 3 Speed Cast Iron Pump - 41 ft Head - 3/4" Pipe
Payments: 
Return Policy: We accept return within 30 days of receipt of your orders. Restocking fee applies on some returned Products. Returned Items shall have intact labels, packages and shall not have been used. for more info.
Full refund if you do not receive your ordered items. - Partial Refund for partially not received or damaged items
Full refund if you do not receive your ordered items. - Introduction & components
- Pump Curve & Specifications
- Technical Documents
-
What is a DIY Pumping Station?
Pumping Stations are an assembly of pump and fittings destined to circulate heat transfer fluid between Heat Source (Vacuum Tube Solar Collector) and a Heat Sink (Solar thermal Storage tank). Most Factory Pre-assembled pumping stations are expensive to buy and offer little or low pumping head (less than 18 ft in total head). For Installation requiring multiple solar panel with longer distances between heat source and heat sink, client is forced to either buy multiple solar pumping stations or split his solar installation into a set of parallel independent ones. In both cases, project cost increases exponentially.
Our DIY Pumping Station offer more pumping head without the frills of factory built pumping stations that customers never make use of. Our DIY Pumping Stations are shipped in pieces (completely Knocked down) and must be assembled by installer.
This Pumping Station offers 1.5 times the head of CALEFFI COMMERCIAL SOLAR PUMP STATION NA255160 at almost half the price.
PSAMR3FV120 Components
Description Qty Unit PS-AMR3FV1TW-20 (Pumping Station without Expansion Tank) Aquamotion TWIN AMR-FV3 - Cast Iron 3 Speeds Pump with built in Check Valve (Rated 250⁰F) 1 Pc Aquamotion FK75 - Cast Iron Flange Adapters 3/4" NPT 1 Pair 3/4" NPT x 3/4" BSPT Nipple 2 Pc 3/4" BSPT Solar Filling Valve with Garden Hose Connectors 1 Pc 3/4" BSPT threaded Female Tee 1 Pc 3/4" BSPT threaded Male Tee 1 Pc 3/4" Female BSPT x 3/4" Male BSPT Ball Valve for Expansion Tank Connection 1 Pc 3/4" Female BSPT x 3/4" Female BSPT Ball Valve 1 Pc 3/4" BSPT x 3/4" BSPT Nipple 2 Pc Pressure Safety Valve 3/4" BSPT 1 Pc PSET2.120 - Expansion Tank Kit (Optional) 3/4" BSPT Cir-Clip (Stainless Steel Washer, Brass Nut and Teflon Gasket) 2 Pc 3/4" Female NPT x 3/4" Male BSPT Adapter 1 Pc Flexible Corrugated Stainless Steel Pipe - 3/4" (20mm OD x 16mm ID) - Non Insulated - 18" Long 1 Pc Expansion Tank - 2.1 US Gallons - 3/4" NPT Male Threaded 1 Pc -
APPLICATION
AquaMotion designed the new TwinTurbo™ Series for residential and commercial applications. The TwinTurbo™ series consists of two AMR circulators, pre-wired, set on medium or high speed, installed in series doubling the performance output of a single circulator.
MATERIALS OF CONSTRUCTION
- Wear Ring, Bearing Support Cartridge Sleeve, Rotor Sleeve Rotor cover : Stainless Steel.
- Motor Housing: Steel.
- Shaft: Aluminum Oxide Ceramic.
- Radial Bearings: Carbon Impregnated.
- Pump housing (closed systems):Cast Iron.
- Pump housing (open system): Stainless Steel.
- O-Ring and Gaskets : Ethylene Propylene Rubber.
- Impeller: Polypropylene.
SPECIFICATIONS
- Maximum water temperature 110°C/230°F.
- Maximum working pressure 125 psi.
- Maximum ambient temperature with a 230°F fluid is 104°F.
- Minimum inlet pressure 20 psi.
- Electrical Rating 120V, 60Hz.
- Integrated Check Valve is rated at 250°F.
PUMP CURVE
-
